ford sync not working after battery change

Following are the common issues that arise after the Ford key fob battery change. Manually Reboot Ford SYNC.

Pin On Truck

Here is the procedure 1- Pressed the mode switch several times to make sure I did not put the.

. An audio message will play SYNC will start rebooting to update. However you are facing new problems after the key fob battery change. When Sync 3 is fully loaded insert the USB stick.

Once the new battery is in place replace the. Now that same button just lowers the volume. Phone feature stopped working after battery died.

Automatic Pressing of Buttons. And in not doing so they got loose when I yanked the positive cluster around to get the battery out. The system reset is designed to restore functionality that has stopped working and does not delete any data that you have stored.

AC Heater Radio defrosters etc. Press and hold both the Power button center of the volume knob and the Seek Right button for 10 seconds. Get Inside Your Car.

Insert the drive into your Ford vehicles USB port. The first thing to do if you run into Ford Sync Bluetooth audio not working is to completely. Normally I press a button on my steering wheel and it says Sync - please say a command.

I tried factory reset and master reset already. USB sometimes wont work at all until car is turned off. Ad Talk to a Car Mechanic Online for Help w Maintenance Troubleshooting and Repair.

Download this package ZIP 44KB and extract it on a USB stick the USB stick needs to in ex-fat format Enter your vehicle and switch on the engine. Find your phones Bluetooth menu. An aqua blue plug and a black cable with a little 10mm nut.

This should now have produced a new log file. After you have replaced the battery get inside your vehicle and close all doors. Find your phones Bluetooth menu tap Off tap On.

If you have Navi you go to the screen to download or install. If this does not work continue to steps 3 and 4. Once the cover is off.

Posted October 24 2020. On SYNC turn Bluetooth Off then On. Get Inside Your Car.

If the connection times out or attempts to take longer than a minute cancel the connection on your phone and go to Tip 4. After you have replaced the battery get inside your vehicle and close all doors. Phone feature stopped working after battery died.

Pull fuse 32 or 33 its one of these two I just cant remember on the cabin fuse panel or disconnect the negative terminal on the battery. 3- Removed the two screws holding the unit to the ceiling and pulled the unit. Radio wont work after battery disconnect.

There are two you should disconnect when changing the battery. This will last from 10 to 20 minutes depending on the size of the installed file. Manually connect the phone with SYNC.

From the front to release the two clips. Press Menu Sync Settings press OK Install on Sync press OK Select Yes. Install the SYNC fuse.

Press the radio power button to turn it on. Unit in the blank mode accidently did not work 2- Checked the 75 A fuse number 10 and it was Ok. That will power off the sync module and allow it to reboot should work fine after rebooting.

So my Sync 3 worked fine on the way to Walmart -- but when I started it up to come home the Sync 3 screen was completely black. Once you are comfortably seated in the vehicle and closed all doors turn on your cars electrical ignition. To do this first go to your phones settings and turn Bluetooth off and then back on.

Find the Bluetooth menu on your phone. I did not remove them. The first and easiest thing you should try to do to stop Ford Sync not working at all is simply resetting the connection.

Use the flathead screwdriver to carefully pry out the old battery and then insert the new one making sure that the. One of the issues that can commonly pop is a faulty connection between the phone and vehicle. Another option for rebooting is.

Common Problems After Key Fob Battery Change. Car Mechanics Online Now. Cars Chirping Without any Reason.

Find your phones Bluetooth menu tap Off tap On. Next replace it with a new one and restart your truck. The following problems frequently occur.

Press and hold both the Volume Down and Seek Right buttons on the steering wheel controls for 10 seconds. Connect the negative cable to restore power to the electrical components. Then put that stick into your Flex and let it updatethen return to the.

Another reboot procedure in which you have to stop your vehicle engine figure out the fuse box location and remove it from the ford sync system. Manually connect SYNC with the phone. After following this wait for a minute or two.

After deleting everything you start over and pair your phone with the Ford SYNC system of your car. The radio turns on automatically. These issues werent there before the battery change.

Open and close the door. Press the Phone button scroll to System Settings Press OK scroll to Bluetooth Devices Press OK select Off select On. Heres What To Do 1.

Disconnected battery took out sync module fuse and replaced. Through MyFord Touch you will press phone then Bluetooth devices in settings select your phone and finally delete it. Get Expert Repair Parts Guidance in Minutes.

So I downloaded the status checker tool put it on a thumb drive and stuck it in the USB port - and absolutely nothing happened. Sync doesnt initialize properly usb frequently doesnt connect to multiple phones using multiple usb chords buttons dont work when car first starts for sometimes up to 10 minutes. Disconnect the cable from the negative terminal of the battery and wait for a minute.

You should remove both of these before the positive for the ease of moving the cables around. Replace the batteries inside the key fobs. None of the mechanical button inputs worked -- radio power DISP steering wheel controls etc.

After that the battery icon on the dash should flash. Install the SYNC fuse. Looking back on the 2013-16 pages Sync seems to have a history of funky behavior including apparent death followed by.

My battery was flat this morning the garage replaced it but now Sync is being weird. By Gumby Tue Jul 12 2011 1037 pm. The radio turns on automatically when the last digit of the code is entered.

Following this go to your Syncs settings and do the exact same thing. This is because if your doors are left open it could disrupt the key fobs reset process. Wait until an installation complete message appears it may take approximately 1 minute.

Turn your vehicle off Open and close the drivers side door Start the vehicle Wait for a confirmation of the connection to display on your MyFord Touch screen. Delete SYNC from your phone. Turn on the Ignition.

Start by using the small flathead screwdriver to remove the cover from the back of the key fob. The light flashing indicates that the new battery has been registered with the car and You are ready to drive off. Discussion Starter 1 Nov 29 2005.

Turn On Your Vehicle Ignition System.

Doing A Ford Sync Master Reset Five Star Ford North Richland Hills